Is an advanced tool that works automatically to eliminate the feedback sound that often arises when the microphone close to the speaker.This tool is often used in the world of sound system indoors and outdoors.
Problems often occur in the installation of sound systems is the emergence of voice feedback,in addition caused by incorrect speaker placement points or less in line also uses low quality microphones and the bass - treble settings or equalizer are less precise that sounds painful ear emergence .
But all of that can be minimized with the addition of a tool called 'Feedback Destroyer'.With this tool during a feedback is automatically muted so as not sustainable . These tools are in addition to control or eliminate the sound of fast feedback also has a feature that works automatically as well as parametik incoming sound equalizer that is processed so as to produce a more uniform response and sound pleasing to the ear . Midle - bass - treble in order to be balanced . Even if you do not use additional equalizer but the sound produced as already using the equalizer .
This tool works automatically when there is feedback on a particular frequency will automatically scan and voice feedback elimination .
How can these tools after installation of the mixer or after the equalizer and then to an amplifier , or it could be a combination of techniques mounting arrangement as follows :
1 . Mic - mixer - ( Feedback Destroyer ) - amplifiers - speakers
2 . Mic - mixer - equalizer - ( Feedback Destroyer ) - amplifiers - speakers
3 . Mic - mic preamp - ( Feedback Destroyer ) - amplifiers - speakers
4 . If you are using a wireless mic can be directly connected to the Feedback Destroyer because existing mic pre amp with a receiver in such an arrangement > Wireless Mic - ( Feedback Destroyer ) - amplifiers - speakers .
.jpg "Wireless Mic - ( Feedback Destroyer ) - amplifiers - speakers .")
How to setup automatic Feedback Destroyer :
Make sure the numbers appear in the display is the number 3 which shows 'Feedback Destroyer' automatic.If work yet to appear please change the number 3 in a way like this .
1 . When lit for the first time see the number that appears on the display when a 2 dashes ( blank - ) , it still indicates the factory settings ( by pass ) . With the knob is available next to them , rotate it to show to the number 3 ,
2 . Then press the 'save' till the lights go out .
3 . Now you have feedback destroyer in full automatic condition .
Another way of setting :
In this tool generally there are 2 inputs and 2 outputs , when both will function mono then do the following settings :
1. Press both buttons engine L and engine R together until the light is on .
2 .Once the light is on make sure the numbers that appear in figure 3 ( automatic setting ) , if not figure 3 shows a large rotary knob next to the display to show the number 3 .
3. If already to number 3 ,and hit store
4. Engine proces setting is finished and both L and R are already in one unit of work ( mono )
Besides, if you want 2 separate inputs in a state work then do the following settings :
1.Press one may ENGINE L or R , make sure that lights are just one is lit again
2.Check and make sure the numbers that appear in figure 3 ( automatic adjustment )
3.Press the save button to save the changes .
4.Proses finished ,second setting filter buttons work apart ( stereo )
Tips to obtain optimal results :
1 . Open mic volume up sound feedback , when a few seconds immediately lost means it works well .
2 . Move the mic repeatedly until no longer heard the sound feedback .
3 . Turn down the mic volume to taste .
4 . Mic ready to be used .
Thus the explanation of one of the support equipment that is often used in the world of sound system, this tool can also be used a reference from me to music at a studio that has a narrow space so as to minimize noise feedback from the mic to the speakers around it ... So and thx....
Problems often occur in the installation of sound systems is the emergence of voice feedback,in addition caused by incorrect speaker placement points or less in line also uses low quality microphones and the bass - treble settings or equalizer are less precise that sounds painful ear emergence .
But all of that can be minimized with the addition of a tool called 'Feedback Destroyer'.With this tool during a feedback is automatically muted so as not sustainable . These tools are in addition to control or eliminate the sound of fast feedback also has a feature that works automatically as well as parametik incoming sound equalizer that is processed so as to produce a more uniform response and sound pleasing to the ear . Midle - bass - treble in order to be balanced . Even if you do not use additional equalizer but the sound produced as already using the equalizer .
.jpg "Feedback Destroyer") |
| Feedback Destroyer |
This tool works automatically when there is feedback on a particular frequency will automatically scan and voice feedback elimination .
How can these tools after installation of the mixer or after the equalizer and then to an amplifier , or it could be a combination of techniques mounting arrangement as follows :
1 . Mic - mixer - ( Feedback Destroyer ) - amplifiers - speakers
2 . Mic - mixer - equalizer - ( Feedback Destroyer ) - amplifiers - speakers
3 . Mic - mic preamp - ( Feedback Destroyer ) - amplifiers - speakers
4 . If you are using a wireless mic can be directly connected to the Feedback Destroyer because existing mic pre amp with a receiver in such an arrangement > Wireless Mic - ( Feedback Destroyer ) - amplifiers - speakers .
.jpg "Wireless Mic - ( Feedback Destroyer ) - amplifiers - speakers .")
How to setup automatic Feedback Destroyer :
Make sure the numbers appear in the display is the number 3 which shows 'Feedback Destroyer' automatic.If work yet to appear please change the number 3 in a way like this .
1 . When lit for the first time see the number that appears on the display when a 2 dashes ( blank - ) , it still indicates the factory settings ( by pass ) . With the knob is available next to them , rotate it to show to the number 3 ,
2 . Then press the 'save' till the lights go out .
3 . Now you have feedback destroyer in full automatic condition .
Another way of setting :
In this tool generally there are 2 inputs and 2 outputs , when both will function mono then do the following settings :
1. Press both buttons engine L and engine R together until the light is on .
2 .Once the light is on make sure the numbers that appear in figure 3 ( automatic setting ) , if not figure 3 shows a large rotary knob next to the display to show the number 3 .
3. If already to number 3 ,and hit store
4. Engine proces setting is finished and both L and R are already in one unit of work ( mono )
Besides, if you want 2 separate inputs in a state work then do the following settings :
1.Press one may ENGINE L or R , make sure that lights are just one is lit again
2.Check and make sure the numbers that appear in figure 3 ( automatic adjustment )
3.Press the save button to save the changes .
4.Proses finished ,second setting filter buttons work apart ( stereo )
Tips to obtain optimal results :
1 . Open mic volume up sound feedback , when a few seconds immediately lost means it works well .
2 . Move the mic repeatedly until no longer heard the sound feedback .
3 . Turn down the mic volume to taste .
4 . Mic ready to be used .
Thus the explanation of one of the support equipment that is often used in the world of sound system, this tool can also be used a reference from me to music at a studio that has a narrow space so as to minimize noise feedback from the mic to the speakers around it ... So and thx....